| A research title and outline |
Name |
Position |
| Research & development of a robot that can carry a heavy load and travel on an irregular ground in a factory |
Shuro Nakajima |
Chiba Institute of Technology, Faculty of Engineering, Associate professor |
| Research on high-accuracy grinding process of high-functional hard-machining materials |
Akihisa Kubota |
Kumamoto University, Graduate School of Science and Technology, Assistant professor |
| Picometer positioning system for ultraprecise machine tools |
Hiroshi Mizumoto |
Tottori University, Faculty of Engineering, Professor |
| Basic research on cutting mechanisms and cutting characteristics in ultrasonic vibration side facing by a square end mill based on a rotary direction change by a helical tooth vibrated in the spindle direction |
Hiroyasu Iwabe |
Niigata University, Graduate School of Science and Technology, Associate professor |
| High-accuracy freedom 6 parallel mechanism driven by 3 plane linear motors |
Kiyoshi Takamasu |
The University of Tokyo, Graduate School of Engineering, Professor |
| Research on burrs produced in ultraprecise micro-cutting |
Kouichi Okuda |
University of Hyogo, Graduate School of Engineering, professor |
| Proposal of a multi-input/output contouring control method for machine tools and reduction of consumption power |
Naoki Uchiyama |
Toyohashi University of Technology, Department of Mechanical Engineering, Assistant Professor |
| Development of a basic production engineering & skill acquirement support system by virtual training and on-the-job training |
Keiichi Watanuki |
Saitama University, Graduate School of Science & Engineering, Professor |
| Research on high-accuracy & high-efficiency grinding of a micro pipe interior by magnetic functional fluid |
Hitoshi Nishida |
Toyama National College of Technology, Department of Mechanical Engineering, Professor |
| Application of SDSM for air spindles and cutting tools |
Masaki Izawa |
Toyama National College of Technology, Department of Mechanical Engineering, Associate professor |
| Machining accuracy prediction model for an end cutting edge of an end mill |
Hirohisa Narita |
Nagoya Institute of Technology, Graduate School of Science & Engineering, Assistant Professor |
| High-accuracy machine tool using a low-thermal expansion cast material |
Minoru Hatate |
Kinki University, School of Engineering, Professor |
| High-dignity precise micro laser machining of high-functional ceramics |
Yasuhiro Okamoto |
Okayama University, Graduate School of Science and Technology, Assistant Professor |
| Ultraprecise diamond cutting tool for long life |
Shouichi Shimada |
Osaka Electro-Communication University, Faculty of Engineering, Professor |
| Research on handling environmental perception and object by a humanoid robot with 3-axis antenna sensors |
Masahiro Ohka |
Nagoya University, Graduate School of Information Science, Associate professor |
| Evaluation of multi-tasking turning center performance by cutting a truncated cone |
Masaomi Tsutsumi |
Tokyo University of Agriculture and Technology, Graduate School of Bio-Applications & System Engineering, Professor |
| Development of a tool attitude decision method for high-speed feed machining by a simultaneously controlled multi-axis machine tool |
Jun-ichi Kaneko |
Saitama University, Graduate School of Science and Engineering Research, Assistant professor |
| Development of a robust inexpensive machine tool based on power measurement by a reaction observer |
Kiyoshi Ohishi |
Nagaoka University of Technology, Faculty of Engineering, Professor |
| Research on estimation of gripping error in small lot end milling of thin parts |
Kouji Teramoto |
Muroran Institute of Technology, Faculty of Engineering, Associate professor |
| Research on creation and practical realization of a hard nitride thin film for dry cutting |
Hiroyuki Hasegawa |
Okayama University, Graduate School of Science and Technology, Assistant professor |
| Surface integrity prediction system for a 5-axis controlled end-milled face |
Hiroyuki Sasahara |
Tokyo University of Agriculture and Technology, Institute of Symbiotic Science and Technology, Associate professor |
| Small-diameter tool (end mill) path creation method for longer life |
Souichi Ibaraki |
Kyoto University, Graduate School of Engineering, Associate professor |
| Development of 3D shape following laser machining system for smoothing die & mold machining |
Haruhisa Sakamoto |
Sophia University, Department of Science and Sngineering, Associate professor |
| Research on creation of complicate hole interior fin shape by electric discharging |
Tohru Ishida |
Osaka University, Graduate School of Engineering, instructor |
| Research on temperless laser hardening |
Muneharu Kutsuna |
Nagoya University, Graduate School of Engineering, Professor |
| Development of ultra high-sensitive linear encoder by noise diffusion restraint method |
Tomoaki Ueda |
Integrated Research Institute at Tokyo Institute of Technology, Specially appointed professor |
